Wood Lathe Safety: Keep Your Lathe In Good Condition

Power tools such as table saws and wood lathes are inherently dangerous although the wood lathe is likely one the safest of the larger power tools in the woodworking shop. Yet there are some considerations in the maintenance of a wood lathe that keep safety standards high.

Maintenance for the wood lathe may be channelled into three categories, long term, regular and steady. For the amateur woodturner this can for all intents and purposes be thought of as yearly, monthly, and by the session. With a little thought and preparation, this need not be a tedious set of procedures but simply a part of the woodturning experience. Too often we ignore the bigger parts of a lathe until they break. This causes frustration an interruption in work flow that may last for weeks waiting for parts.

Yearly maintenance looks at the overall health of the lathe. Wood lathes rotate wood between head stocks and tail stocks while allowing the turner to move tools back and forth to remove wood. This means there are bearings for things that rotate, motors that drive the rotations, belts to move power from one location to another, and metal sliding on metal to allow tools to move.

The simplest of these to check is the sliding of tools rests and tailstocks over the ways of a lathe to manoeuvre tools and hold wood. If there is hesitation in the movement of either it is usually due to rust on the ways or finishes that have hardened on the metal. Remove the tailstock and the tool rest banjo from the lathe and check for either on the bottom of each. Clean rust and finish from the ways, banjo and tailstock with fine sandpaper, steel wool or cleaner and apply wax to the ways for easier movement and rust prevention before replacing the tailstock and banjo.

Check belts for wear and replace them from spare belts that you have on hand. Belts tend to be the inexpensive side of lathe repair and it is good to have a spare one in the shop. Likewise, bearing will likely announce incipient wear with noise or movement and should be ordered before demanding replacement. Each lathe is slightly different for bearing replacement so follow your manufacturers advice.

At least monthly blow any dust out of the motor and inspect the wiring for good repair. Mounting bolts can loosen with vibration from turning wood and should be checked for tightness. This is a good time to look at belts and bearings for wear and to order new ones for the annual checkup.

Before every turning session make sure that the lathe is not crowded with other tools and there is plenty of room to move around it while turning. Be sure all tools are sharp and the sharpening station is ready to go with a cleaned wheel. Just before turning the lathe on check one more time to be certain the moving wood will clear the tool rest and all parts of the lathe are tightened down.

Very quickly this all becomes second nature and adds to the enjoyment of turning wood. The satisfaction of knowing the tools are in order will only add to the satisfaction and pleasure of the wood turning experience.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Getting the Woodturner Ready To Turn

Woodworking is a reasonably dangerous hobby or occupation. By that, I mean that a bit of reason does a lot to remove many dangers. Wood lathes are among the safest of woodworking stationary tools because, unlike table and band saws, instead of wood heading into a moving blade, a hand held blade is directed into the moving wood. However, it is still necessary to do some basic preparation in order to ensure safety at the wood lathe.

While woodturners are good to ready the lathe by making wood and machinery secure and the tools sharpened, they also need to prepare themselves for a safe experience. Amateurs in particular turn wood when opportunity presents itself, often after a hard day at work. This can mean a drowsy period and it should not be spent near power tools. Such time is better spent first having a nap or even cleaning the shop. Sometimes all that is needed to clear the cobwebs is a bit of simple movement in a pleasant atmosphere.

It should not need to be said, but the woodturning shop with its chain saws, wood lathes, and band saws is not the place for alcohol or drugs, including prescription drugs or over the counter medications. Check with your doctor for side effects including drowsiness before turning while using medications.

It is necessary to dress for woodturning. Loose clothing can easily catch on spinning wood, especially rough or burled pieces. A turner can easily be caught and hauled into the lathe. Considering that even small lathes often have half horsepower motors, this can be extremely dangerous. Neckties and jewellery are particularly to be avoided. Even rings can be caught on the spinning wood resulting in an accident called degloving wherein the bone is left on the finger and the skin and muscles are removed. A small turned box near the lathe for rings and other jewellery is a good reminder of safety first.

Clothing that is tight at the cuffs and neck prevents annoying and distracting shavings from becoming an irritant against the skin. Face masks and goggles prevent flying wood from doing damage to the face and eyes while dust masks can prevent damage to the lungs.

Many turners forget the dangers of chemicals in finishes. Latex or vinyl gloves help prevent contact problems and a good chemical mask can prevent lung damage. Even better is the use of finishes that are safe for breathing and contact.

Safety is an issue that faces all of us at the wood lathe. It is possible to use common sense and be safe in this very enjoyable craft for a lifetime of shavings.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Five Things To Consider For Woodturning Workshops

Of all the power tools in the work shop, the wood lathe is one of the safest. This is still a powerful tool used with sharp tools and care is needed. Ultimately, safety is in the hands of the user. Here are a few safety tips to consider when turning wood.

One of the first things to look for is the general condition of the lathe itself. Many woodturners are amateurs who have only a few hours a week to spend in the workshop and wish to spend most of it at the lathe so that maintenance takes a back seat. Some time needs to be spent on such maintenance as sharpening spur centers, replacing bearings, making sure mounting nuts are secure, dressing the tool rest and so on. Before the lathe is turned on it should be checked to be sure that everything is tightened down and the wood will clear the tool rest as it rotates. Not only does it make the turning more enjoyable, it makes it safer.

While the condition of the lathe is important for safety, so is the condition of the wood turner. Fatigue causes accidents. A wood turner should be well rested and free of alcohol or drugs. All rings and other jewellery should be removed. It is all too easy for rotating wood to catch neck ties or other loose clothing and draw a turner into the lathe or for a caught piece of jewellery to rip off pieces of skin.

The height of the lathe should generally be set so that the center line of the turning will be at elbow height of the turner. This may vary a little with individuals because of varying ratios of arm to leg length, but it is a good working estimate. A height too great or too little easily causes back pain through undue hunching or stretching. Rubber mats on concrete floors also can be a big help in relieving back pain.

With the increase in artistic turning over the past few decades, more and more wood turners are mounting burls, spalted wood and wood with splits and voids in it, particularly in faceplate work. These pieces of wood tend to be fairly large and unbalanced. This sets up a lot of vibration in the lathe and can be inherently dangerous, especially as chunks of wood may fly off the lathe at high speeds if the lathe is turning too fast. Experience and slow speeds are essential in this type of turning.

There are various charts that are used to determine the speeds at which woods of various diameters are turned. These should be approached with caution as not all woods are of the same density and many have knots, hidden splits or other imperfections that will be aggravated by high speeds. It is best to start turning at a slow speed and increase as circumstances dictate.

There is no way to make working with power tools completely safe but a few simple precautions and common sense can make the woodturning workshop a safe place for a long time to come.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Getting the Woodturner Ready To Turn

Woodworking is a reasonably dangerous hobby or occupation. By that, I mean that a bit of reason does a lot to remove many dangers. Wood lathes are among the safest of woodworking stationary tools because, unlike table and band saws, instead of wood heading into a moving blade, a hand held blade is directed into the moving wood. However, it is still necessary to do some basic preparation in order to ensure safety at the wood lathe.

While woodturners are good to ready the lathe by making wood and machinery secure and the tools sharpened, they also need to prepare themselves for a safe experience. Amateurs in particular turn wood when opportunity presents itself, often after a hard day at work. This can mean a drowsy period and it should not be spent near power tools. Such time is better spent first having a nap or even cleaning the shop. Sometimes all that is needed to clear the cobwebs is a bit of simple movement in a pleasant atmosphere.

It should not need to be said, but the woodturning shop with its chain saws, wood lathes, and band saws is not the place for alcohol or drugs, including prescription drugs or over the counter medications. Check with your doctor for side effects including drowsiness before turning while using medications.

It is necessary to dress for woodturning. Loose clothing can easily catch on spinning wood, especially rough or burled pieces. A turner can easily be caught and hauled into the lathe. Considering that even small lathes often have half horsepower motors, this can be extremely dangerous. Neckties and jewellery are particularly to be avoided. Even rings can be caught on the spinning wood resulting in an accident called degloving wherein the bone is left on the finger and the skin and muscles are removed. A small turned box near the lathe for rings and other jewellery is a good reminder of safety first.

Clothing that is tight at the cuffs and neck prevents annoying and distracting shavings from becoming an irritant against the skin. Face masks and goggles prevent flying wood from doing damage to the face and eyes while dust masks can prevent damage to the lungs.

Many turners forget the dangers of chemicals in finishes. Latex or vinyl gloves help prevent contact problems and a good chemical mask can prevent lung damage. Even better is the use of finishes that are safe for breathing and contact.

Safety is an issue that faces all of us at the wood lathe. It is possible to use common sense and be safe in this very enjoyable craft for a lifetime of shavings.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood lathe safety: Keep the lathe In good condition

Power tools such as saws and table wooden Lathes are inherently dangerous even if the wood lathe is probably the most secure one of the greatest tools in wood shop. Yet there are some considerations in the maintenance of a wood lathe that maintain high safety standards.

Maintenance for the wood lathe can be channelled into three categories, the long term, regular and constant. For the amateur woodturner this can all be thought of as the annual, monthly, and from the session. With a little thought and preparation, this is not necessary a boring set of procedures, but simply a part of lathe experience. Too often ignore the parties larger than a lathe, until they break. This causes frustration a break in the workflow that can last for weeks waiting for parts.

Annual maintenance Check overall health of the lathe. Wood Wood lathes rotates between head and tail of the stocks, while allowing the turner move tools back and forth to remove the wood. This means that there are things which pivot bearings, motors that drive the rotations, belts to move power from one location to another and metal sliding on metal to allow the tools to move.

Is the simplest of these to control scrolling breaks tools and tailstock over ways of operating a lathe tools and keep the wood. If there is hesitation in the movement of both which is usually due to rust on ways or finishes that have hardened on the metal. Remove the tailstock and banjo rest lathe tool and check both on the bottom of each. Clean the rust and finish modes, banjo and tailstock with sandpaper, steel wool or cleaning and apply wax to ways to prevent movement and rust easier before replacing tailstock and banjo.

Check belts for wear and replace them by spare belts that you have at your fingertips. Belts tend to be the economic side of repairing lathe and is good to have a spare one in the store. Similarly, bearing probably will announce incipient wear with noise or movement, and must be ordered before requesting the replacement. Any lathe is slightly different for replacement of bearing so follow your advice.

At least monthly blow any dust out of the engine and inspect the wiring for repair. Mounting bolts may loosen with vibration to transform wood and should be checked for tightness. This is a good time to look at belts and bearings for wear and order new ones for the annual check-up.

Before each session to ensure that the lathe turning is not crowded with other instruments and there is not much room to move while turning. Ensure that all tools are sharp and sharpening station is ready to go with a clean wheel. Just before turning lathe control once again to be sure that the wood will eliminate the rest moving tool and all parts of the lathe are tightened down.

Very quickly this becomes second nature and it adds enjoyment to turn the wood. The satisfaction of knowing that the tools are sorted only add to the satisfaction and pleasure of wood by transforming the experience.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Turning safety: wheel shape.

Woodworking tend to like any physical activity, woodturning, many woodturners still than to take care of their own equipment woodworking take better. Some considerations are for continued enjoyment of our technology.

Unless very wheel pens, candlesticks, etc. is limited to small pieces tuner part handles most of the wood. Above Bowl blank 100 pounds, a rough cut of wood logs to go Bowl Turner anomaly is not, and turning spaces mount them in a bowl. Before you jump of woodturners in stretching and warm-up process the weight lifting weight while most barbell and dumbbell is much more awkward shaped more wood to grab, lift. Understandably, pulled muscles and poor backup results neither serious turned ardour.

A few minutes between the fun before basic warm-up and stretching exercises, wood processing, can go a long way to add to the sessions of the Potter's wheel. Such practices are seen in books, magazines and websites easily.

Is to one bowl and spindle rotation before warmups best simply green tree from or shavings. Standing tool in turning and held to the side and up and down the arm while tool mobile slight bend forward and legs and waist twists rotates. During the conversion and very often exaggerate these movements, body, place especially incredible in various parts of the legs, waist, hips and back strain. Movement of these muscles are warmed up and ready to back to the basics.

12 Or 14, Mount 3 or 4 inch prepares a green tree Center between branch and roughing gouges. You can use the dry wood is easier and less strain on green tree. The roughing gouge from the right edge quite upright posture turn left. Use the opposite hand and move the rest of the tools from the left edge to the right turn. Repeat the steps to wood care is too small. You must muscle the armed ready for a real project.

The Woodturners to bend and reach awkward poses, and that no distortion tends to place should be put in place. However, many to keep healthy and of safety and enjoyment to continue rotating in years future, can do.

Wood turnings Darrell Feltmate around Woods , its web site that contains detailed information on the conversion of a novice or an experienced Turner is a wood Turner for screening, as well as a collection for your viewing pleasure. This is the place to start here can you also learn about trees. How it looks? Sharp reaches many free video site dealing with Bowl.

Is a tree of some to fully explain the project web site. In particular, photos of beginner project description and procedures complete Beginner project page.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Keep Your Lathe In Good Condition

Power tools such as table saws and wood lathes are inherently dangerous although the wood lathe is likely one the safest of the larger power tools in the woodworking shop. Yet there are some considerations in the maintenance of a wood lathe that keep safety standards high.

Maintenance for the wood lathe may be channelled into three categories, long term, regular and steady. For the amateur woodturner this can for all intents and purposes be thought of as yearly, monthly, and by the session. With a little thought and preparation, this need not be a tedious set of procedures but simply a part of the woodturning experience. Too often we ignore the bigger parts of a lathe until they break. This causes frustration an interruption in work flow that may last for weeks waiting for parts.

Yearly maintenance looks at the overall health of the lathe. Wood lathes rotate wood between head stocks and tail stocks while allowing the turner to move tools back and forth to remove wood. This means there are bearings for things that rotate, motors that drive the rotations, belts to move power from one location to another, and metal sliding on metal to allow tools to move.

The simplest of these to check is the sliding of tools rests and tailstocks over the ways of a lathe to manoeuvre tools and hold wood. If there is hesitation in the movement of either it is usually due to rust on the ways or finishes that have hardened on the metal. Remove the tailstock and the tool rest banjo from the lathe and check for either on the bottom of each. Clean rust and finish from the ways, banjo and tailstock with fine sandpaper, steel wool or cleaner and apply wax to the ways for easier movement and rust prevention before replacing the tailstock and banjo.

Check belts for wear and replace them from spare belts that you have on hand. Belts tend to be the inexpensive side of lathe repair and it is good to have a spare one in the shop. Likewise, bearing will likely announce incipient wear with noise or movement and should be ordered before demanding replacement. Each lathe is slightly different for bearing replacement so follow your manufacturers advice.

At least monthly blow any dust out of the motor and inspect the wiring for good repair. Mounting bolts can loosen with vibration from turning wood and should be checked for tightness. This is a good time to look at belts and bearings for wear and to order new ones for the annual checkup.

Before every turning session make sure that the lathe is not crowded with other tools and there is plenty of room to move around it while turning. Be sure all tools are sharp and the sharpening station is ready to go with a cleaned wheel. Just before turning the lathe on check one more time to be certain the moving wood will clear the tool rest and all parts of the lathe are tightened down.

Very quickly this all becomes second nature and adds to the enjoyment of turning wood. The satisfaction of knowing the tools are in order will only add to the satisfaction and pleasure of the wood turning experience.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Getting the Woodturner Ready To Turn

Woodworking is a reasonably dangerous hobby or occupation. By that, I mean that a bit of reason does a lot to remove many dangers. Wood lathes are among the safest of woodworking stationary tools because, unlike table and band saws, instead of wood heading into a moving blade, a hand held blade is directed into the moving wood. However, it is still necessary to do some basic preparation in order to ensure safety at the wood lathe.

While woodturners are good to ready the lathe by making wood and machinery secure and the tools sharpened, they also need to prepare themselves for a safe experience. Amateurs in particular turn wood when opportunity presents itself, often after a hard day at work. This can mean a drowsy period and it should not be spent near power tools. Such time is better spent first having a nap or even cleaning the shop. Sometimes all that is needed to clear the cobwebs is a bit of simple movement in a pleasant atmosphere.

It should not need to be said, but the woodturning shop with its chain saws, wood lathes, and band saws is not the place for alcohol or drugs, including prescription drugs or over the counter medications. Check with your doctor for side effects including drowsiness before turning while using medications.

It is necessary to dress for woodturning. Loose clothing can easily catch on spinning wood, especially rough or burled pieces. A turner can easily be caught and hauled into the lathe. Considering that even small lathes often have half horsepower motors, this can be extremely dangerous. Neckties and jewellery are particularly to be avoided. Even rings can be caught on the spinning wood resulting in an accident called degloving wherein the bone is left on the finger and the skin and muscles are removed. A small turned box near the lathe for rings and other jewellery is a good reminder of safety first.

Clothing that is tight at the cuffs and neck prevents annoying and distracting shavings from becoming an irritant against the skin. Face masks and goggles prevent flying wood from doing damage to the face and eyes while dust masks can prevent damage to the lungs.

Many turners forget the dangers of chemicals in finishes. Latex or vinyl gloves help prevent contact problems and a good chemical mask can prevent lung damage. Even better is the use of finishes that are safe for breathing and contact.

Safety is an issue that faces all of us at the wood lathe. It is possible to use common sense and be safe in this very enjoyable craft for a lifetime of shavings.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathe Safety: Five Things To Consider For Woodturning Workshops

Of all the power tools in the work shop, the wood lathe is one of the safest. This is still a powerful tool used with sharp tools and care is needed. Ultimately, safety is in the hands of the user. Here are a few safety tips to consider when turning wood.

One of the first things to look for is the general condition of the lathe itself. Many woodturners are amateurs who have only a few hours a week to spend in the workshop and wish to spend most of it at the lathe so that maintenance takes a back seat. Some time needs to be spent on such maintenance as sharpening spur centers, replacing bearings, making sure mounting nuts are secure, dressing the tool rest and so on. Before the lathe is turned on it should be checked to be sure that everything is tightened down and the wood will clear the tool rest as it rotates. Not only does it make the turning more enjoyable, it makes it safer.

While the condition of the lathe is important for safety, so is the condition of the wood turner. Fatigue causes accidents. A wood turner should be well rested and free of alcohol or drugs. All rings and other jewellery should be removed. It is all too easy for rotating wood to catch neck ties or other loose clothing and draw a turner into the lathe or for a caught piece of jewellery to rip off pieces of skin.

The height of the lathe should generally be set so that the center line of the turning will be at elbow height of the turner. This may vary a little with individuals because of varying ratios of arm to leg length, but it is a good working estimate. A height too great or too little easily causes back pain through undue hunching or stretching. Rubber mats on concrete floors also can be a big help in relieving back pain.

With the increase in artistic turning over the past few decades, more and more wood turners are mounting burls, spalted wood and wood with splits and voids in it, particularly in faceplate work. These pieces of wood tend to be fairly large and unbalanced. This sets up a lot of vibration in the lathe and can be inherently dangerous, especially as chunks of wood may fly off the lathe at high speeds if the lathe is turning too fast. Experience and slow speeds are essential in this type of turning.

There are various charts that are used to determine the speeds at which woods of various diameters are turned. These should be approached with caution as not all woods are of the same density and many have knots, hidden splits or other imperfections that will be aggravated by high speeds. It is best to start turning at a slow speed and increase as circumstances dictate.

There is no way to make working with power tools completely safe but a few simple precautions and common sense can make the woodturning workshop a safe place for a long time to come.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.