Wood Lathes? - A Couple of Things to Think About When Buying a Used One

Wood lathes come on the used market in a fairly regular fashion and can be a great way to get a good wood lathe for the money. On the other hand some of the used lathes are lemons. Here are a few suggestions for the shopping trip.

First of all have some idea of what you want to do with a wood lathe in your shop. If you are upgrading from your present machine then you have some opinions as to what things are needed. The novice buyer has a harder road to follow.

There are two main ways to turn wood, spindle and faceplate. Spindle turning includes such things and chair and table legs and is normal way to general woodworkers to enter the woodturning world. Making turned legs for a table eventually leads to making a table as an excuse for turning legs. Faceplate work includes pieces such as round table tops, bowls and vases. Most people who take up faceplate work desire to turn bowls and go from there.

Most beginner lathes will be suitable for spindles and bowls. Older wood lathes used a system of working over the bed of the lathe for spindles and at the other end of the headstock worked "offside" for bowls and such. This required faceplates and other materials to have "left handed" threads. In effect, the bother of setting up for outboard turning meant that most woodturners could not be bothered and settled for making the largest bowl that would fit over the lathe bed. Today's manufacturers often compromise with a headstock that rotates and allows for bigger pieces using the same holding equipment as over the bed.

The problem that arises with this setup comes from lathe speeds. Generally spindles are turned much faster than faceplate work. Large bowl blanks, if unbalanced as most are, can at high speeds shake a lathe apart; cause the lathe to walk across the floor; or turn the wood into a projectile. At slow speeds none of these occur. Six hundred rpm is just slow enough for a twelve inch bowl, but slower is better.

So when looking for a lathe, get one that fits your preferred style of turning. For spindles a solid set of ways making up the lathe bed are important. Faceplate lathes should be very sturdy at the headstock, handle a large piece of wood, and have a low speed. Remember that a wood lathe is a basic power tool and look for the finish and quality you would normally desire in a good tool.

Wood lathes are a lot of fun in the woodworking shop. There are some great bargains on the used market and with a bit of insight, a used lathe is a wonderful way to get started in the woodturning craft.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood lathes? -A couple of things to think about when you buy a used one

Wooden Lathes are on the market used in fairly regular and can be a great way to get a good wood lathe for the money. On the other hand some of lathes used are lemons. Here are some suggestions for the shopping trip.

First of all get an idea of what you want to do with a wood lathe in your shop. If you are upgrading from your machine this then you have some opinions about what things are necessary. The novice buyer has a tougher road to follow.

There are two main ways to turn wood, Chuck and front. Turning spindle includes such things and the Chair and table legs and is the normal way of carpenters General to enter the world of the lathe. Manufacture turned legs to a table at the end to make a table as an excuse to turn her legs. Faceplate work includes pieces such as round table tops, bowls and vases. Most people who take different types work the desire to transform the bowls and go from there.

Most beginner lathes will be suitable for spindles and bowls. Older wood lathes used a system of work above the bed of lathe chucks and at the other end of the headstock worked "offside" for bowls and the like. This required forms and other materials to have discussions "Lefty". In fact, the hassle of setting for outboard turning the meaning that most of the Turners could not be bothered and settled to make it the biggest Bowl that would fit over the bed of lathe. The producers of today often compromise with a blade that rotates and allows larger pieces using the same equipment company as above the bed.

The problem that arises with this setting is from tornio speed. Generally chucks are made much faster working different types. Blanks large bowl, if unbalanced as most are high-speed, shake a lathe part; cause the lathe on foot through the floor; or transform the wood into a bullet. Low-speed, none of these occur. 600 rpm is just slow enough for a twelve-inch Bowl, but more slowly, is better.

So when looking for a lathe, get one that fits your favorite style of turning. For chucks a solid set of ways that make up the bed lathe are important. Lathe faceplate should be very robust blade, handle a large piece of wood and has a low speed. Remember that a wood lathe is an instrument of power base and look for the finish and quality that normally would have desired a good tool.

Wooden Lathes are a lot of fun in store. There are some great deals on the second-hand market and with a little understanding, a lathe used is a wonderful way to start in craft lathe.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.

Wood Lathes? - A Couple of Things to Think About When Buying a Used One

Wood lathes come on the used market in a fairly regular fashion and can be a great way to get a good wood lathe for the money. On the other hand some of the used lathes are lemons. Here are a few suggestions for the shopping trip.

First of all have some idea of what you want to do with a wood lathe in your shop. If you are upgrading from your present machine then you have some opinions as to what things are needed. The novice buyer has a harder road to follow.

There are two main ways to turn wood, spindle and faceplate. Spindle turning includes such things and chair and table legs and is normal way to general woodworkers to enter the woodturning world. Making turned legs for a table eventually leads to making a table as an excuse for turning legs. Faceplate work includes pieces such as round table tops, bowls and vases. Most people who take up faceplate work desire to turn bowls and go from there.

Most beginner lathes will be suitable for spindles and bowls. Older wood lathes used a system of working over the bed of the lathe for spindles and at the other end of the headstock worked "offside" for bowls and such. This required faceplates and other materials to have "left handed" threads. In effect, the bother of setting up for outboard turning meant that most woodturners could not be bothered and settled for making the largest bowl that would fit over the lathe bed. Today's manufacturers often compromise with a headstock that rotates and allows for bigger pieces using the same holding equipment as over the bed.

The problem that arises with this setup comes from lathe speeds. Generally spindles are turned much faster than faceplate work. Large bowl blanks, if unbalanced as most are, can at high speeds shake a lathe apart; cause the lathe to walk across the floor; or turn the wood into a projectile. At slow speeds none of these occur. Six hundred rpm is just slow enough for a twelve inch bowl, but slower is better.

So when looking for a lathe, get one that fits your preferred style of turning. For spindles a solid set of ways making up the lathe bed are important. Faceplate lathes should be very sturdy at the headstock, handle a large piece of wood, and have a low speed. Remember that a wood lathe is a basic power tool and look for the finish and quality you would normally desire in a good tool.

Wood lathes are a lot of fun in the woodworking shop. There are some great bargains on the used market and with a bit of insight, a used lathe is a wonderful way to get started in the woodturning craft.

This post was made using the Auto Blogging Software from WebMagnates.org This line will not appear when posts are made after activating the software to full version.